NEW ARRIVALS
MDMP5V2
HK 90 SERIES PICTINNY RAIL MOUNT GEN 2
  • Picatinny Rail Mount GEN 2 for HK® MP5/ CETME/ 90 Series of long guns.
  • Clamps directly to the top of the HK® Spec stamped receivers: MP5, SP89, HK91/ HK93/ HK94
  • Mount to HK® Claw Mount type lugs on stamped receivers.
  • Length: 3.8"
  • Weight: 2.5 oz.
TMP1522
Barrel Nut Wrench for M&P® 15-22 .22LR
  • Barrel Nut Wrench for the Smith & Wesson® M&P® 15-22 .22LR
  • This tool is for tightening or for the removal of the factory Smith & Wesson® M&P® 15-22 .22LR barrel nut.
  • Smith & Wesson® M&P® 15-22 .22LR barrel nut have been known to come loose over time, now you have the tool to tighten the factory barrel nut.
  • If you plan on swapping out the factory handguards, you may need this tool to get the factory handguards off.
  • NcSTAR has KeyMod® free float handguards made specifically for the Smith & Wesson® M&P® 15-22 .22LR.
  • Tool has machined teeth to interface with the Smith & Wesson® M&P® 15-22 .22LR factory barrel nut. Also has flats on the opposite side for a wrench to tightening or loosening the barrel nut. Tools is hollow and is designed to slide over the barrel.
  • Black anodized finish, aluminum construction.
  • Length: 11.0'
  • Diameter: 1"
  • Weight: 12.8 oz.
VTARW4
PRO SERIES LOWER RECEIVER TOOL
  • Pro Series AR15 Lower Receiver Wrench - heavy duty purpose built M4 castle nut wrench for collapsible stock buffer tubes
  • Large heavy duty cross section makes it easier on the hands to work on your AR lower receiver.
  • You can remove/install M4 castle nuts with ease with this AR wrench. The castle nut wrench slips over the castle nut and nearly encompasses the castle nut for a more secure fit when installing or removing the M4 castle nut. Makes for assembling/installing collapsible stock buffer tubes a super easy task.
  • The other end of the wrench is for installing/removing A2 Rifle buffer tubes (¾")".
  • 1/2" and 3/8" drive compatible, for torquing your barrel nuts to the proper torque specifications.
  • All the tools are Clearly Labeled.
  • Hole at the end is for hang
  • Steel Construction
  • Length: 12.5"
  • Weight: 18 oz.
  • US Patent Pending
VAML1CB
M-LOK Covers/Blk/18 Pk
  • M-LOK® Single Slot Covers installs into individual M-LOK® slots for making M-LOK® handguards more comfortable and to insulate the shooter's hands from the heat of the barrel.
  • Made from rubber material that is textured to provide a comfortable and sure grip surface.
  • Very easy to install. Lift rear hinged half and slide the front shoe into the M-LOK® slot, press down on the rear hinged section to lock the M-LOK® cover in place.
  • Heat resistant material will insulate the M-LOK® handguard from rapid sustained semi-auto fire.
  • Available in 4 colors: Black, Tan, Green, Urban Gray.
  • Length: 0.8"
  • Height: Adds 0.15" above the M-LOK® handguard surface.
  • The M-LOK® Slot Covers come in a pack of 18 each.
  • US PATENT
VAML1CG
M-LOK Covers/Grn/18 Pk
  • M-LOK® Single Slot Covers installs into individual M-LOK® slots for making M-LOK® handguards more comfortable and to insulate the shooter's hands from the heat of the barrel.
  • Made from rubber material that is textured to provide a comfortable and sure grip surface.
  • Very easy to install. Lift rear hinged half and slide the front shoe into the M-LOK® slot, press down on the rear hinged section to lock the M-LOK® cover in place.
  • Heat resistant material will insulate the M-LOK® handguard from rapid sustained semi-auto fire.
  • Available in 4 colors: Black, Tan, Green, Urban Gray.
  • Length: 0.8"
  • Height: Adds 0.15" above the M-LOK® handguard surface.
  • The M-LOK® Slot Covers come in a pack of 18 each.
  • US PATENT
VAML1CT
M-LOK Covers/Tan/18 Pk
  • M-LOK® Single Slot Covers installs into individual M-LOK® slots for making M-LOK® handguards more comfortable and to insulate the shooter's hands from the heat of the barrel.
  • Made from rubber material that is textured to provide a comfortable and sure grip surface.
  • Very easy to install. Lift rear hinged half and slide the front shoe into the M-LOK® slot, press down on the rear hinged section to lock the M-LOK® cover in place.
  • Heat resistant material will insulate the M-LOK® handguard from rapid sustained semi-auto fire.
  • Available in 4 colors: Black, Tan, Green, Urban Gray.
  • Length: 0.8"
  • Height: Adds 0.15" above the M-LOK® handguard surface.
  • The M-LOK® Slot Covers come in a pack of 18 each.
  • US PATENT
VAML1CU
M-LOK Covers/Ugr/18 Pk
  • M-LOK® Single Slot Covers installs into individual M-LOK® slots for making M-LOK® handguards more comfortable and to insulate the shooter's hands from the heat of the barrel.
  • Made from rubber material that is textured to provide a comfortable and sure grip surface.
  • Very easy to install. Lift rear hinged half and slide the front shoe into the M-LOK® slot, press down on the rear hinged section to lock the M-LOK® cover in place.
  • Heat resistant material will insulate the M-LOK® handguard from rapid sustained semi-auto fire.
  • Available in 4 colors: Black, Tan, Green, Urban Gray.
  • Length: 0.8"
  • Height: Adds 0.15" above the M-LOK® handguard surface.
  • The M-LOK® Slot Covers come in a pack of 18 each.
  • US PATENT
VAARVGFLKM
VERTICLE GRIP FLASHLIGHT/ KEYMOD
  • Ultra Bright 3W 250 Lumen CREE® LED flashlight with crenellated bezel with ring selector for: full power, strobe, and half power features.
  • Lightweight ergonomically textured grip.
  • Features a unique and inovative ambidextrous switch design. There are rocker switches on both sides of the vertical grip. Press the rocker switch down for momentary on and press up to lock the switch into the on position. There is also an extender lever "gas pedal" that can be mounted onto either side for thumb activation when griping the vertical grip hand.
  • Three light modes: Full power (250 lumen), Half power (150 lumens), and Strobe (250 lumens)
  • This model mounts to KeyMod™ spec handguards.
  • Uses two CR123A batteries (included).
  • Length: 7.5"
  • Height: 4.25
  • Width: 2.5"
  • Vertical grip and flashlight is also available with Picatinny or M-LOK® mounts.
  • US Patent Pending
VAARVGFLML
VERTICLE GRIP FLASHLIGHT/ M-LOK
  • Ultra Bright 3W 250 Lumen CREE® LED flashlight with crenellated bezel with ring selector for: full power, strobe, and half power features.
  • Lightweight ergonomically textured grip.
  • Features a unique and inovative ambidextrous switch design. There are rocker switches on both sides of the vertical grip. Press the rocker switch down for momentary on and press up to lock the switch into the on position. There is also an extender lever "gas pedal" that can be mounted onto either side for thumb activation when griping the vertical grip hand.
  • Three light modes: Full power (250 lumen), Half power (150 lumens), and Strobe (250 lumens)
  • This model mounts to M-LOK® handguards.
  • Uses two CR123A batteries (included).
  • Length: 7.5"
  • Height: 4.25
  • Width: 2.5"
  • Vertical grip and flashlight is also available with Picatinny or KeyMod™ mounts.
  • US Patent Pending
VAARVGFLPR
VERTICLE GRIP FLASHLIGHT/ PICATINNY
  • Ultra Bright 3W 250 Lumen CREE® LED flashlight with crenellated bezel with ring selector for: full power, strobe, and half power features.
  • Lightweight ergonomically textured grip.
  • Features a unique and inovative ambidextrous switch design. There are rocker switches on both sides of the vertical grip. Press the rocker switch down for momentary on and press up to lock the switch into the on position. There is also an extender lever "gas pedal" that can be mounted onto either side for thumb activation when griping the vertical grip.
  • Three light modes: Full power (250 lumen), Half power (150 lumens), and Strobe (250 lumens)
  • This model mounts to Weaver, Picatinny, MIL-STD 1913 type rails.
  • Uses two CR123A batteries (included).
  • Length: 7.5"
  • Height: 4.25
  • Width: 2.5"
  • Vertical grip and flashlight is also available with KeyMod™ or M-LOK® mounts.
  • US Patent Pending
VDBSOL130
SPD SOLAR REFLEX SIGHT/ BLACK
  • SPD has a dual power source. The Red Dot reflex optic can be powered by the sun via the top mounted solar cell or the included AA battery.
  • Solar cells mounted on top of the reflex sight will power the red dot whenever there is sufficient sun light on the solar cells. The Red Dot automatically turns on whe there is sufficient sun light.
  • The SPD Red Dot can also be powered by the AA battery. AA battery should be used when there isn't enough sun light, when using the optics indoors, or when using the optic at night.The electronic control panel has a red LED indicator when the Red Dot is powered by the AA battery.
  • Features an electronic control panel to turn on the Red Dot under AA battery power. You can adjust the brightness level up or down when powered by the battery.
  • Red Dot centerline is at 1.5" AR15 height.
  • Locking quick release Picatinny mount.
  • Unlimited eye relief.
  • LED 100% safe for the eyes.
  • 2 MOA Red Dot has 5 levels of brightness.
VTGLKPBL
DISASSEMBLY & FRONT SIGHT TOOL - FOR GLOCK®
  • Tactical tool designed in a pen configuration with a steel disassembly and front sight tool for Glock® pistols.
  • Anodized blue aluminum pen tool with two threaded caps that thread into the center body, with a black steel pocket clip.
  • Hardened steel 3/32" or 2.5mm punch tool for all Glock® pistols. Designed to remove the pins and disassemble the Glock® frame, slide, and the magazine into their individual components.
  • The opposite end of the tool includes a 3/16" hex nut driver for removing/installing factory and aftermarket Glock® front sights. The 3/16" hex nut driver features an internal magnet to conveniently hold the front sight screw as you install the front sight post.
  • The pointed cap can be used to center the pins in the frame. Pointed cap can be screwed onto the pocket clip cap to prevent losing it when the tool is in use.
  • Length: 3.4"
  • Weight: 4.0 oz.
  • DISCLAIMER: “GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. or GLOCK Ges.mbH. Neither “NcSTAR Inc. & VISM” nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.mbH. The use of “GLOCK” on this page is merely to advertise the sale of GLOCK tools, mounts, or optics. For genuine GLOCK, Inc. and GLOCK Ges.mbH products and parts visit www.glock.com.
VAPFLSGV3
GEN3 Pistol Flashlight w/Strobe & Green Laser
  • GEN3 Pistol Flashlight with Strobe & Green Laserwith Picatinny Mount
  • Electronic Control Buttons are completely Ambidextrous; there are four button on each side of the Pistol Flashlight and Laser body. There is a Flashlight Momentary button on top, Flashlight Constant On/Off button on the bottom, the Middle button turns the Laser On/Off, and the Flashlight Strobe button is at the front.
  • Momentary & Constant On/Off buttons are positioned and angled ergonomically. They are accessible from your Trigger Finger or your support hand thumb when gripping the pistol.
  • 3W Ultra Bright 200 Lumen CREE® LED flashlight
  • Slides onto most Weaver / Picatinny / MIL-STD 1913/ Pistol accessory spec rails
  • Fully Adjustable Green Laser: 532nm, Max output <5mw, Class IIIa Laser
  • Dimensions: 3.4L x 1.5W x 1.6H
  • Weight: 4.0 oz. with Battery
  • Black Anodized Aluminum body
  • Uses 1 each CR123A Battery (Included)
  • US PATENT PENDING
VAPFLSRV3
GEN3 Pistol Flashlight w/Strobe & Red Laser
  • GEN3 Pistol Flashlight with Strobe & Red Laser with Picatinny Mount
  • Electronic Control Buttons are completely Ambidextrous; there are four button on each side of the Pistol Flashlight and Laser body. There is a Flashlight Momentary button on top, Flashlight Constant On/Off button on the bottom, the Middle button turns the Laser On/Off, and the Flashlight Strobe button is at the front.
  • Momentary & Constant On/Off buttons are positioned and angled ergonomically. They are accessible from your Trigger Finger or your support hand thumb when gripping the pistol.
  • 3W Ultra Bright 200 Lumen CREE® LED flashlight
  • Slides onto most Weaver / Picatinny / MIL-STD 1913/ Pistol accessory spec rails
  • Fully Adjustable Red Laser: 635-655nm, Max output <5mw, Class IIIa Laser
  • Dimensions: 3.4L x 1.5W x 1.6H
  • Weight: 4.0 oz. with Battery
  • Black Anodized Aluminum body
  • Uses 1 each CR123A Battery (Included)
  • US PATENT PENDING
VAPTLG
Pistol Green Laser with Strobe
  • Pistol Green Laser with Strobe feature, Picatinny Mount
  • Electronic Control Buttons are completely Ambidextrous; there are three buttons on each side of the Pistol Laser body. There is a Momentary button on top, Constant On/Off button on the bottom, and the Laser Strobe button is at the front.
  • Momentary & Constant On/Off buttons are positioned and angled ergonomically. They are accessible from your Trigger Finger or your support hand thumb when gripping the pistol.
  • Slides onto most Weaver / Picatinny / MIL-STD 1913/ Pistol accessory spec rails
  • Fully Adjustable Green Laser: 532nm, Max output <5mw, Class IIIa Laser
  • Dimensions: 3.4L x 1.5W x 1.3H
  • Weight: 4.1 oz. with Battery
  • Black Anodized Aluminum body
  • Uses 1 each CR123A Battery (Included)
  • US PATENT PENDING
VAPTF
Pistol Flashlight with Strobe
  • Pistol Flashlight with Strobe feature, Picatinny Mount
  • Electronic Control Buttons are completely Ambidextrous; there are three buttons on each side of the Pistol Flashlight body. There is a Momentary button on top, Constant On/Off button on the bottom, and the Flashlight Strobe button is at the front.
  • Momentary & Constant On/Off buttons are positioned and angled ergonomically. They are accessible from your Trigger Finger or your support hand thumb when gripping the pistol.
  • 3W Ultra Bright 200 Lumen CREE® LED flashlight
  • Slides onto most Weaver / Picatinny / MIL-STD 1913/ Pistol accessory spec rails
  • Dimensions: 3.4L x 1.5W x 1.3H
  • Weight: 3.8 oz. with Battery
  • Black Anodized Aluminum body
  • Uses 1 each CR123A Battery (Included)
  • US PATENT PENDING
VAARVGKM
KeyMod™ Short Vertical Grip - Black
  • KeyMod™ Short Vertical Grip with battery storage compartment.
  • Ergonomic shape for a comfortable and secure grip. Texture front, side panels, and rear grip surfaces.
  • Mounts onto KeyMod™ slots without the need of any tools. Pull out the grips internal core and with a simple twist you can secure the grip to your KeyMod™ slotted handguards.
  • Center core also can store a single CR123A or small parts. Sloted storage door that twists on/off.
  • Injection molded polymer construction with steel KeyMod™ hardware.
  • Dimensions: 3.0"H X 2.2"L X 1.3"W
  • Weight: 2.8 oz.
VAGPARB
AR15 Ergonomic Pistol Grip w/ Storage
  • Ergonomic AR-15 Pistol Grip with Storage Compartment
  • Mounts onto AR-15/ M4/ M16 lower receivers.
  • Ergonomic design to fit comfortably in the Operators hand. Front and rear textured grip surface for comfort and secure gripping surfaces.
  • Storage Compartment can store two each CR123A batteries, spare parts, or emergency survival supplies
  • Renforced Polymer Construction
  • Includes mounting screw.
  • Dimensions: 4.2"H X 2.8"L X 1.1"W
  • Weight: 2.3 oz.
VAFLFSP
AR15 Flashlight with A2 Iron Front Sight Post
  • AR15/M4 LED Flashlight with Strobe and A2 Iron Front Sight Post
  • 3 Watt Bright CREE® LED Flashlight, 200 Lumens Peak Output.
  • A2 Front Sight Post is at the 1.5" AR15 Height for back-up iron sights. A2 Post is adjustable for elevation.
  • Ambidextrous button arrangement, two button on each side for Momentary (rear button) and Constant On/Off (forward button). Buttons are easily accessible from your support hand when grasping handguard.
  • Back of flashlight features a rear mounted button for the Flashlight Strobe feature and a 3.5 mm jack in the back for the included remote momentary pressure switch.
  • Mounts onto Weaver/ Picatinny/ MIL-STD 1913 type rails.
  • Flashlight can extend past the edge of the handguard with the cantilever style mount design, preserving rail space and for making a more comfortable hold on the shorter carbine Picatinny handguards.
  • Die Cast Aluminum Body with Black Anodized body
  • Uses 1 CR123A Lithium Type Battery (Included)
  • Dimensions: 3.5"L X 1.6"H X 1.4"D
  • Weight 4.2 oz. without pressure swicth
  • Weight 4.6 oz. with pressure swicth
  • US PATENT PENDING
VMTAKKM
AK KeyMod Mount Receiver Cover
  • AK KeyMod Receiver Cover for mounting KeyMod mounts and accessories directly to your receiver cover.
  • Replaces existing AK-47 receiver cover. Fits AKM pattern rifles with a stamped receiver (7.62X39, 5.54X39, .223)
  • The mount provides a low profile KeyMod mounting surface on three sides of the Receiver Cover. For mounting an optic mount and accessories to onto the top or sides of the receiver cover of your AKM pattern rifle.
  • The top KeyMod surface is pre-drilled for mounting an NcSTAR Micro Dot directly to the top of your AK with the lowest possible mounting height. This allows the NcSTAR Micro Dot to Co-Witness with AK Iron Sights.
  • Three front tabs and two rear screws are provided for a secure fit.
  • Aluminum (Rail) and Steel Construction (Receiver Cover)
  • Length: 9.5"
  • Weight: 7.3 oz.
VMKMQSM
KeyMod™ QD Sling Mount
  • KeyMod™ QD Sling Mount adapter for quick detachable slings and sling swivel mounts.
  • KeyMod™ QD Sling Mount, designed to mount onto KeyMod™ handguards.
  • Low profile design.
  • Mounts onto handguard via two KeyMod™ feet.
  • Black anodized aluminum construction.
  • Mounting tool included
  • ** QD Sling Swivel not included (3rd picture)
VTARW3
Pro Series AR Barrel Wrench
  • Pro Series AR15 Barrel Wrench - heavy duty purpose built barrel wrench
  • Large heavy duty cross section makes it easier on the hands to work on your AR upper.
  • You can remove/install GI barrel nuts with ease with this AR wrench. Makes for assembling/installing barrels and free float handguards a super easy task.
  • The other end of the wrench is for installing/removing 5/8" muzzle brakes and flash suppressors.
  • 1/2" and 3/8" drive compatible, for torquing your barrel nuts to the proper torque specifications.
  • All the tools are Clearly Labeled.
  • Hole at the end is for hanging tool on a wall peg, nail/screw.
  • Steel Construction
  • Length: 12.5"
  • Weight: 23 oz.
  • US Patent Pending

NcSTAR Inc.

1(866)627-8278

Email:info@ncstar.com

Address:18031 Cortney Ct.

City of Industry

CA 91748 USA